The CBTLV16800 provides 20-bits of high-speed bus switching with low on-state resistance of the switch allowing connections to be made with minimal propagation delay. The device also precharges the B port to a user-selectable bias voltage (BIASV) to minimize live-insertion noise
Renesas Electronics RAA271082 Automotive PMIC is an adaptive multi-rail power supply IC consisting of one primary side high voltage synchronous step-down regulator, two secondary side low voltage synchronous step-down regulators and one LDO regulator. The RAA271082 features four overvoltage and undervoltage monitors, I2C communications, a universal I/O pin, and a dedicated reset output/fault indicator.
Maxim Integrated MAX20079 36V step-down Converter is a small automotive grade synchronous step-down converter with integrated high side and low side switches. The device provides up to 3.5A current with input voltages ranging from +3V to +36V and static current of only 3.5μA when unloaded. MAX20079 supports ±2% accurate output voltage in the normal operating input range of +6V to +18V.
The RT9193 is designed for portable RF and wireless applications with demanding performance and space requirements. The RT9193 performance is optimized for battery-powered systems to deliver ultra low noise and low quiescent current. A noise bypass pin is available for further reduction of output noise
The ISL6244 provides core-voltage regulation by driving 2 to 4 interleaved synchronous-rectified buck-converter channels in parallel. Interleaving the channel timing results in increased ripple frequency which reduces input and output ripple currents. The reduction in ripple results in lower component cost, reduced dissipation, and a smaller implementation area.
The HIN232A high-speed RS-232 transmitter/receiver interface circuit meets all ElA high-speed RS-232E and V.28 specifications, and is particularly suited for those applications where 12V is not available. They require a single +5V power supply and feature onboard charge pump voltage converters which generate +10V and -10V supplies from the 5V supply.
The Allegro ACS712 provides economical and precise solutions for AC or DC current sensing in industrial, commercial, and communications systems. The device package allows for easy implementation by the customer. Typical applications include motor control, load detection and management, switchmode power supplies, and overcurrent fault protection. The device is not intended for automotive applications
The PCM56 is a state-of-the-art, fully monotonic, digital-to-analog converter that is designed and specified for digital audio applications. This device employs ultra-stable nichrome (NiCr) thin-film resistors to provide monotonicity, low distortion, and low differential linearity error (especially around bipolar zero) over long periods of time and over the full operating temperature.
The LTC2158-14 is a 2-channel simultaneous sampling 310Msps 14-bit A/D converter designed for digitizing high frequency, wide dynamic range signals. It is perfect for demanding communications applications with AC performance that includes 68.8dB SNR and 88dB spurious free dynamic range (SFDR). The 1.25GHz input bandwidth allows the ADC to undersample high frequencies with good performance. The latency is only six clock cycles.
TDK introduced the ModCap HF modular high-frequency power capacitor with modular design concept for DC support applications. The new B25647A * series components not only have ultra-high switching frequency, but also provide six newly developed models, covering the rated voltage of 900 V to 1600 V, the capacitance range of 640 µ F to 1850 µ F, the rated current range of 160 A to 210 A (depending on the model), and the maximum allowable hot spot temperature of 90 ° C.
Diodes introduced a highly integrated dual channel USB Type-C protocol decoder for various opportunities of rapid increase in charging of USB pre installed in the vehicle. The AP43776Q supports USB Power Transfer (PD) 3.1 Standard Power Range (SPR), Programmable Power Supply (PPS), and Quick Charge QC5 fast charging protocol. This product also supports the old battery charging (BC) 1.2, which optimizes the performance of the multi port USB device charging system.
The UA78L00 series of fixed-voltage linear regulators is designed for a wide range of applications. These applications include on-card regulation for elimination of noise and distribution problems associated with single-point regulation as well as for voltage regulation in major appliances.
The MAX1776 high-efficiency step-down converter provides an adjustable output voltage from 1.25V to VIN from supply voltages as high as 24V. An internal current-limited 0.4Ω MOSFET delivers load currents up to 600mA. Operation to 100% duty cycle minimizes dropout voltage (240mV at 600mA).
The ISL6292D is an integrated single-cell Li-ion or Li-polymer battery charger capable of operating with an input voltage as low as 2.4V. This charger is designed to work with various types of ac adapters or a USB port.
The AD73360 is a six-input channel analog front-end processor for general purpose applications including industrial power metering or multichannel analog inputs. It features six 16-bit A/D conversion channels each of which provide 77 dB signal-tonoise ratio over a dc to 4 kHz signal bandwidth. Each channel also features a programmable input gain amplifier (PGA) with gain settings in eight stages from 0 dB to 38 dB.
The DS87C520/DS83C520 EPROM/ROM high-speed microcontrollers are fast 8051-compatible microcontrollers. They feature a redesigned processor core without wasted clock and memory cycles. As a result, the devices execute every 8051 instruction between 1.5 and 3 times faster than the original for the same crystal speed. Typical applications will see a speed improvement of 2.5 times using the same code and the same crystal.
TDK announced the expansion of its SmartAutomotive Safety Integrity Rating (ASIL) and non-ASIL Motion Sensor product line. InvenSense IAM-20380HT monolithic integrated MEMS and ASIC triaxial MotionTracking sensor platform solutions for non-safety automotive applications, including IAM-20380HT triaxial MEMS gyroscope and DK-20380HT development suite.
The DS1267 Dual Digital Potentiometer Chip consists of two digitally controlled, solid-state potentiometers. Each potentiometer is composed of 256 resistive sections. Between each resistive section and both ends of the potentiometer are tap points which are accessible to the wiper. Three standard resistance values are available, including 10, 50 and 100 kohm versions. The device is available in a 14-pin DIP, 16-pin SOIC and 20-pin TSSOP package.
